Cut-to-length-lines

Material Width 2.000 mm︱Material Thickness 1,50 - (5,00)6,00 mm︱Coil Weight max. 30,0 t︱Coil Inside Diameter 580 mm︱Coil Outside Diameter 1.250/1.500 mm︱

---

sheet length 580 - 6.000 mm working direction left - right otherwise according to technical specification 05.68-1.0

sheet width 500 - 1350 mm︱plate thickness 0,3 - 3 mm︱no. of strokes Hub/min︱Control ︱total power requirement kW︱weight of the machine ca. t︱dimensions of the machine ca. m︱

---

Stainless steel Cut to Length Line(Flying type) - Material: stainless steel, surface treated steel -- Thickness: 0.3–3 mm (as of stainless steel) -- Width: 500-1350 mm -- Trim: 5-25 mm on one side (more than twice the plate thickness) - Material coil: internal diameter 508 mm, external diameter 600–1800 mm -- weight maximum 15 tons -- Width accuracy: 500–1350 mm plus or minus 0.2 mm (when side trimming) -- Product length: 400–6000 mm Plus/minus 0.3 mm - 6-leveler (6-hi) leveler x 2units types -- Tension: 45 to 50 kg/mm2 -- Yield point: 28 kg/mm2 - Cutting method: Cut while running (flying), numerically controlled rocking type - flying shears -- (Cutting speed) 20–40/80 m/min -- Speed 2-speed change type --- 0.3 to 1.2 mm: 20 to 80 m/min --- 0.21–3 mm: 20–40 m/min -- Slow operation: 0.8 m/min -- Conveyor speed: 20~120m/min -- Cut count: up to 150 cuts/min -- (Product piling) --- Plate width: 500–1350 mm --- No1 piler: 400 to 3100 mm (also used as a reject filer) --- No2 piler: 400–6100 mm --- Load height: up to 600mm --- Load weight: up to 4 tons Line direction: From right to left on control panel Line: Approximately 13 m x 49.050 m (Major facilities) - Coil skid - Coil car - Pay off reel and a paper winder - Coil opener - Rough Leveler - Shear - No. 1 Looper Guide - Side guide and pinch roller - Side trimmer - Scrap winder x2 - No.1 Finisher Leveler (6-hi) - No2 Finisher Leveler (6-hi) - No 2 Looper Guide - Measuring roller, feed roller and paper-off reel - Shear - Conveyor - Cart - No1/No2 piler type - Hydraulic unit: Type - Valve stand type - (Coil skid) -- V-type fixed skid -- Coil maintenance: 1 coil -- Coil weight: up to 15 tonnes -- Coil diameter: 600 to 1800 mm -urethane rubber (Coil Car) Cradle roller type Hydraulic boost Electricity transfer driving type Two guide lots hydraulic cylinder elevating type (payoff reel and paper winder) Overhang, single-mant 4-segment type Paper reel motor: DC 5.5KW 400/1600 RPM, attached to brake Paper winder: cone type, (motor DC 1.5KW, 1750 RPM) (Coil Opener) Knife edge method (Rough Leveler) 2-stage (2hi) 5-body roller leveler Pinch rollers: 160 mm × 1450 mm 2 pieces, The upper part of the pinch roller is hydraulic cylinder press-down, and the lower roller is fixed 5 workload rollers 130mm x 1450mm The upper roller of the workload roller is electrically pressed, and the lower roller is fixed 0–40/80 m/min Two-stage change 0.3 to 1.6 mmt: 80 m/min 1.7 to 1.6 mmt: 40 m/min Motor: DC 18.5 KW, 1750 RPM, Brake Attachment Pressing motor: 2 1.5KW 100RPMs with brakes (Shear) Hydraulic up cut shear Knife size: 25 mm thickness × 150 mm width × 1450 mm length (No. 1 Looper Guide) Table lift Hydraulic cylinder operation method Loop: Light Volume Control Method Roller: 70 mm diameter × 1450 mm × 6 bonds, rubber lining roller (Side guide and pinch roller) Vertical Free Roller Electrically switched type Side guide roller: 90 mm diameter × 150 mm length × 6 bones Pinch Roller: 2nd Stage (2hi) Roller: 160 mm diameter × 1450 mm length × 2 bones Upper roller: pneumatic cylinder pressure free roller Lower Roller: Fixed Drive Roller (Side trimmer) Overhang Drive Cut 0–40/80 m/min 2-stage change type 0.3 to 1.6 mmt: 80 m/min 1.7 to 1.6 mmt: 40 m/min Cutter diameter: 320 mm / 190 mm internal diameter × 20 mm thickness Roller: 320 mm external diameter × 19 mm internal diameter × 20 mm thickness Motor: DC 5.5KW 1750RPM (Scrap winder) Two machines Link Pin Gauge Type (Hydraulic Cylinder Opening and Closing Type) Motor: 2 DC 2.2KW 1450 RPM (No1 Finisher Leveler) 6-level (6-hi) 17 leveler Thickness: 1.21–3.0 mm Speed: 6 to 40/80 m/min Thickness 0.3–1.2 mm 6–80 m/min Thickness 1.21–3 mm 6–40 m/min Pinch roller: 180 mm × 1750 mm × 2 bones The upper roll is a pneumatic cylinder. The lower roll is fixed Rubber lining drive roller Work roll: 60mm x 1750mm x 17e 8 for the upper roll, 9 for the lower roll Plated abrasive roller Medium roller: 50 mm × 1750 mm × 19 pieces 9 for the upper roll, 10 for the bottom roll Backup Roller: 88 mm Diameter x 50 mm Length x 7 rows Pressing Method: Lower Roller Parallel Pressing Pressing speed: 0.25 mm/sec Pressurization: plus or minus 5 mm Motor: DC 55KW 1750 RPM Brake Attachment (No2 Finisher Leveler) 6-level (6-hi) 17 leveler Plate thickness: 0.3–1.2 mm Speed: 5 to 80 m/min Pinch roller: 180 mm × 1750 mm × 2 bones The upper roll is a pneumatic cylinder. The lower roll is fixed Rubber lining drive roller Work roll: 35mm x 1750mm x 17bon 8 for the upper roll, 9 for the lower roll Plated abrasive roller Medium Roller: 32 mm × 1750 mm × 19 pieces 9 for the upper roll, 10 for the bottom roll Backup Roller: 99 mm Diameter x 50 mm Length x 7 rows Roller bearing type Pressing Method: Lower Roller Parallel Pressing Pressing speed: 0.25 mm/sec Pressurization: plus or minus 5 mm Motor: DC 35KW 1750RPM Brake Attachment (No. 2 Looper Guide) Table lift Hydraulic cylinder operation method Loop: How to control the amount of light (amount of light) Roller: 70 mm diameter × 1450 mm × 6 bonds, rubber lining roller (Measuring roll/feed roller/paper vinyl payoff reel) Measuring roller: The upper roll is pneumatic pressing, the lower roll is fixed, the pressing amount is 30 mm Feed roller: Upper roll is pneumatic cylinder press, lower roll is fixed, press load is 40 mm Motor: DC 2.2KW 1750RPM (Shear) Fluctuating Flying shear 0.3~3mm Speed: 2 groups of 20–40/80 m/min Thickness 0.3–1.6 mm 80 m/min Tlate thickness 1.6–3 mm 40 m/min Cut count: up to 150 cuts/min Cutting length: 400–6000 mm Electric up CUT shear Cut up and down knife die via motor, reducer, pinion stand crankshaft Knife: 20 mmt × 80 mm × 1400 mm × 1 set The top knife is a straight knife, and the bottom is a V-lock knife Adjustment: Wedge Motor: DC 75KW 550RPM (Conveyor) Belt conveyor type Belt width: 1200 mm Conveyor length: 3800 mm Motor DC 5.5KW 1450RPM Brake Attachment (No. 1 No. 2 piler) No1 piler: Combined use of reject truck, air blower Combined use of side conveyor No2 piler: Combined suction conveyor and air blower Loading height: 600 mm Lift: Hydraulic lift volume 650 mm Motor: 4 1.5KW 150RPM units for side guide end stoppers 2.2 KW 1500RPM for lifters 1.5KW for cart 7.5KW for blower (Hydraulic device) 70 kg/cm2 × 100 L/min Pen pump Motor: DC 18.5 KW 1000 RPM (Supply power) AC400 V,50 Hertz 3 Phase / AC200 V,50 Hertz 3 Phase (Control power) AC 200V, 50 Hz Single Phase (Compressed air) Compressed air required: 5 kg/cm2

Material Width 1.800 mm︱Material Thickness 0,50-1,50 mm︱Coil Weight 30,0 t︱Required Space app. m︱Machine Weight app. t︱

---

length tolerance ± 0,5 mm width tolerance ± 0,5 mm diagonal tolerance ± 1,0 mm line consisting of: double side decoiler leveler no. of leveling rolls 21 leveling roll diameter 35 mm flying shear magnetic conveyor table - length 10 m 2 output tables electric pneumatic hydraulic

Capacity 26/34/42/48/60 mm ø︱Machine dimensions (lxwxh) - mm︱Machine weight - kg︱

---

Pipe cutting machine

sheet width 3000 mm︱plate thickness 6 mm︱distance between columns / mm︱

---

sheet width 3100 mm︱plate thickness 6 mm︱voltage 380 V︱control CYBELEC CybTouch ︱down holder 14 Stück︱cutting angle 1,2 °︱total power requirement 11 kW︱weight of the machine ca. 6.300 kg︱dimensions of the machine ca. 4000x2100x1640 mm︱

---

Equipment: - CNC electr. / hydraulic swing cut shears - CYBELEC CNC touch screen controller, model CybTouch 8 * Backgauge preselection - X axis * Cutting gap adjustment * Quantity * Cutting length limitation * Material preselection, including sheet thickness * Cutting line lighting - motorized backgauge, travel = 1,000 mm (X axis) * on ball screws * autom. can be folded up at max. Traverse path, for longer cuts - 1x side stop - 2x front support arms - Ball casters in the front support table - hinged finger protection, with safety switch - BOSCH / HOERBIGER hydraulic system - SIEMENS electrical system - light barrier behind the machine (safety device) - foot switch - CE mark / declaration of conformity - User manual: machine u. Control in German Special equipment: - pneumatic sheet holding device (monoblock)

sheet width 3060 mm︱plate thickness 10 mm︱back stop - adjustable 1000 mm︱cutting angle 1,5 °︱weight of the machine ca. 10500 kg︱

---

Equipment/accessories: - CYBELEC Cybtouch touchscreen controller - NC controller for backgauge preselection, cutting gap adjustment, number of pieces, cutting length and material preselection - Sheet holding device - 1 side stop with scale, T-slot and tilting cam - 2 front support arms - Cutting line lighting - Cutting gap adjustment - Cutting length limiter - Hinged finger guard with limit switch - Motorized backgauge 1,000 mm travel - recirculating ball screws - Ball rollers in the table - foot switch

sheet width 2040 mm︱ 4 mm︱sheet thickness for stainless steel 2 mm︱total power requirement 7,5 kW︱rear stop 750 mm︱weight of the machine ca. 2600 kg︱dimensions 2810 x 2230 x 1360 mm︱

---

sheet width 3100 mm︱plate thickness 10 mm︱cutting angle 2 °︱down holder 14 Stück︱no. of strokes 13 Hub/min︱throat 350 mm︱oil volume 260 l︱control CYBELEC CybTouch 8 ︱total power requirement 22 kW︱weight of the machine ca. 10.550 kg︱dimensions of the machine ca. 4000x2250x2050 mm︱

---

Domestic equipments: - Hydraulic swing cut sheet metal shears - Touch screen controller with digital display for backgauge - automatic kerf adjustment via the control - Backgauge control 1000 mm travel with recirculating ball screws - Vibration cutting machine with kerf adjustment - 2 support arms - 1 side stop - Photocell behind the machine - Cutting length limit - cut line lighting - Chrome steel knife - Ball rolls in the table - hinged finger guard with limit switch - Footswitch - CE mark / Declaration of Conformity - Bed instructions in German

sheet width 3100 mm︱plate thickness 10 mm︱cutting angle 2 °︱down holder 14 Stück︱no. of strokes 13 Hub/min︱throat 350 mm︱oil volume 260 l︱total power requirement 22 kW︱weight of the machine ca. 10.550 kg︱dimensions of the machine ca. 4000x2250x2050 mm︱

---

Domestic equipments: - Hydraulic swing cut sheet metal shears - Touch screen controller with digital display for backgauge - automatic kerf adjustment via the control - Backgauge control 1000 mm travel with recirculating ball screws - Vibration cutting machine with kerf adjustment - 2 support arms - 1 side stop - Photocell behind the machine - Cutting length limit - cut line lighting - Chrome steel knife - Ball rolls in the table - hinged finger guard with limit switch - Footswitch - CE mark / Declaration of Conformity - Bed instructions in German

sheet width 3100 mm︱plate thickness 13 mm︱thickness at "Niro-steel" 8 mm︱control CYBELEC CybTouch ︱down holder 14 Stück︱cutting angle 2,0° °︱total power requirement 22 kW︱voltage 380 V︱no. of strokes 11 Hub/min︱weight of the machine ca. 12.100 kg︱dimensions of the machine ca. 4000x2240x2235 mm︱

---

Accessories / equipment: - CYBELEC-CybTouch control panel with digital display for backgauge - hydr. Cutting gap adjustment via control - 1 side stop - 4 front lifting arms - cut line lighting - Cutting gap adjustment - Cutting length limit - Ball rolls in the table - motorized back gauge 1.000 mm travel with recirculating ball screws,    automatically start at the end of the stop - Shear knives for stainless steel cuts as standard - Photocell behind the machine - SIEMENS electrical system - BOSCH / HOERBIGER hydraulic system - Footswitch - Operating instructions in German

sheet width 3100 mm︱plate thickness 6 mm︱voltage 380 V︱control CYBELEC CybTouch ︱down holder 14 Stück︱cutting angle 1,2 °︱ 20 ︱total power requirement 11 kW︱weight of the machine ca. 5700 kg︱dimensions of the machine ca. 4000x2100x1640 mm︱

---

Accessories / equipment: - CYBELEC Cybtouch touch screen controller - NC controller for backgauge, gap adjustment, number of pieces, cutting length - 1 side stop with scale, T-groove and tilting cam - 2 front support arms - cut line lighting - Cutting gap adjustment - Cutting length limit - Folding finger guard with limit switch - motorized back gauge 1.000 mm travel - Ball screws - Photocell behind the machine - Ball rolls in the table - SIEMENS electrical system - BOSCH / HOERBIGER hydraulic system - Footswitch - CE mark / Declaration of Conformity - Operating manual: Machine and control in German

sheet width 1350 mm︱ 3 mm︱sheet thickness for stainless steel 1,5 mm︱rear stop 600 mm︱total power requirement 3 kW︱weight of the machine ca. 1150 kg︱dimensions 2030 x 1940 x 1220 mm︱

---

sheet width 3050 mm︱plate thickness 6 mm︱back stop - adjustable 1000 mm︱cutting angle 1,5 °︱0 17 St.︱total power requirement 11 kW︱quantity of oil 180 l︱weight of the machine ca. 6250 kg︱

---

sheet width 2550 mm︱ 4 mm︱sheet thickness for stainless steel 2 mm︱rear stop 750 mm︱total power requirement 7,5 kW︱weight of the machine ca. 3050 kg︱dimensions 3300 x 2230 x 1360 mm︱

---

sheet width 3100 mm︱plate thickness 4,00 mm︱distance between columns mm︱total power requirement 7,50 kW︱weight of the machine ca. 4,20 t︱dimensions of the machine ca. m︱

---

- CNC controlled back gauge 10 – 1000mm - central cutting gap adjustment - Pneumatic sheet metal support - Angle stop 2500 mm - 3 support arms

sheet width 3050 mm︱plate thickness 16 mm︱distance between columns - mm︱back stop - adjustable 1000 mm︱total power requirement kW︱weight of the machine ca. 15 t︱

---

Acc.: electr. back gauge with DRO, table extensions

sheet width 4000 mm︱plate thickness 13 mm︱distance between columns 4100 mm︱no. of strokes 8 Hub/min︱table height 805 mm︱back stop - adjustable 1000 mm/mn︱column arm 50 mm︱down holder 19 Stück︱oil volume 400 l︱cutting angle 2,3 °︱total power requirement 30,75 kW︱weight of the machine ca. 14,5 t︱dimensions of the machine ca. 4,95 x 3,68 x 2,24 m︱

---

Robust design & powerful body for perfect cutting Hardened and ground blades for long life and precise Proved and rigid design with swing beam top table Minimum deformation and optimum cutting quality with best cutting angle CE standards security The combination of economic and perfect cutting performance CNC controlled gap adjustment User friendly CNC touch screen control unit Sheet support arms Ball transfer tables and T-slot

sheet width 2500 mm︱plate thickness 6 mm︱distance between columns 2600 mm︱no. of strokes 16 Hub/min︱table height 760 mm︱back stop - adjustable 1000 mm/mn︱cutting angle 1,5 °︱column arm 50 mm︱lower gears 13 Stück︱oil volume 200 l︱total power requirement 11,75 kW︱weight of the machine ca. 5,7 t︱dimensions of the machine ca. 3,6 x 3,43x 1,8 m︱

---

Robust design & powerful body for perfect cutting Hardened and ground blades for long life and precise Proved and rigid design with swing beam top table Minimum deformation and optimum cutting quality with best cutting angle CE standards security The combination of economic and perfect cutting performance CNC controlled gap adjustment User friendly CNC touch screen control unit Sheet support arms Ball transfer tables and T-slot

sheet width 3000 mm︱plate thickness 13 mm︱distance between columns 3100 mm︱no. of strokes 8 Hub/min︱table height 805 mm︱back stop - adjustable 1000 mm/mn︱column arm 50 mm︱down holder 15 Stück︱oil volume 400 l︱cutting angle 2,3 °︱total power requirement 30,75 kW︱weight of the machine ca. 11,2 t︱dimensions of the machine ca. 3,95 x 3,64 x 2,10 m︱

---

Robust design & powerful body for perfect cutting Hardened and ground blades for long life and precise Proved and rigid design with swing beam top table Minimum deformation and optimum cutting quality with best cutting angle CE standards security The combination of economic and perfect cutting performance CNC controlled gap adjustment User friendly CNC touch screen control unit Sheet support arms Ball transfer tables and T-slot

sheet width 2000 mm︱plate thickness 6 mm︱distance between columns 2100 mm︱no. of strokes 16 Hub/min︱table height 760 mm︱back stop - adjustable 1000 mm/mn︱cutting angle 1,5 °︱column arm 50 mm︱down holder 10 Stück︱oil volume 200 l︱total power requirement 11,75 kW︱weight of the machine ca. 4,8 t︱dimensions of the machine ca. 3,1 x 3,43 x 1,65 m︱

---

Robust design & powerful body for perfect cutting Hardened and ground blades for long life and precise Proved and rigid design with swing beam top table Minimum deformation and optimum cutting quality with best cutting angle CE standards security The combination of economic and perfect cutting performance CNC controlled gap adjustment User friendly CNC touch screen control unit Sheet support arms Ball transfer tables and T-slot

sheet width 2000 mm︱plate thickness 10 mm︱distance between columns 2100 mm︱no. of strokes 10 Hub/min︱table height 820 mm︱back stop - adjustable 1000 mm/mn︱column arm 50 mm︱down holder 10 Stück︱oil volume 200 l︱cutting angle 1,8 °︱total power requirement 22,75 kW︱weight of the machine ca. 7,8 t︱dimensions of the machine ca. 3,2 x 3,45 x 2,03 m︱

---

Robust design & powerful body for perfect cutting Hardened and ground blades for long life and precise Proved and rigid design with swing beam top table Minimum deformation and optimum cutting quality with best cutting angle CE standards security The combination of economic and perfect cutting performance CNC controlled gap adjustment User friendly CNC touch screen control unit Sheet support arms Ball transfer tables and T-slot

sheet width 3000 mm︱plate thickness 10 mm︱distance between columns 3100 mm︱no. of strokes 10 Hub/min︱table height 805 mm︱back stop - adjustable 1000 mm/mn︱column arm 50 mm︱down holder 15 Stück︱oil volume 300 l︱cutting angle 1,8 °︱total power requirement 22,75 kW︱weight of the machine ca. 9,0 t︱dimensions of the machine ca. 3,94 x 3,56 x 2,09 m︱

---

Robust design & powerful body for perfect cutting Hardened and ground blades for long life and precise Proved and rigid design with swing beam top table Minimum deformation and optimum cutting quality with best cutting angle CE standards security The combination of economic and perfect cutting performance CNC controlled gap adjustment User friendly CNC touch screen control unit Sheet support arms Ball transfer tables and T-slot

sheet width 4000 mm︱plate thickness 10 mm︱distance between columns 4100 mm︱no. of strokes 8 Hub/min︱table height 805 mm︱back stop - adjustable 1000 mm/mn︱column arm 50 mm︱down holder 19 Stück︱oil volume 300 l︱cutting angle 1,8 °︱total power requirement 22,75 kW︱weight of the machine ca. 12 t︱dimensions of the machine ca. 4,94 x 3,58 x 2,22 m︱

---

Robust design & powerful body for perfect cutting Hardened and ground blades for long life and precise Proved and rigid design with swing beam top table Minimum deformation and optimum cutting quality with best cutting angle CE standards security The combination of economic and perfect cutting performance CNC controlled gap adjustment User friendly CNC touch screen control unit Sheet support arms Ball transfer tables and T-slot