Cut-to-length-lines
Machinelist: Cut-to-length-lines
Cut-to-length-lines
- SCHMITT REINHOLD GMBH
- Obernahmerstr. 74
- 58119 Hagen-Hohenlimburg
- Deutschland
-
+49 (0)2334 4847
+49 (0)2334 4840 -
info@reinhold-schmitt.de
www.reinhold-schmitt.de
#2008-056810 · Cut-to-length-lines
VIGANO/RIVA - - - 2000/2001 -
Technical details
sheet length 580 - 6.000 mm working direction left - right otherwise according to technical specification 05.68-1.0
Datasheet
Request / Contact
- Kemmerich Werkzeugmaschinen
- Im Rottfeld 1a
- 40789 Monheim am Rhein
- Deutschland
-
+49 2173 207474
+49 2173 207473 -
info@kemmerich.biz
www.kemmerich.biz
#1020-19439 · Cut-to-length-lines
HITACHI - - - 1993 -
Technical details
Stainless steel Cut to Length Line(Flying type) - Material: stainless steel, surface treated steel -- Thickness: 0.3–3 mm (as of stainless steel) -- Width: 500-1350 mm -- Trim: 5-25 mm on one side (more than twice the plate thickness) - Material coil: internal diameter 508 mm, external diameter 600–1800 mm -- weight maximum 15 tons -- Width accuracy: 500–1350 mm plus or minus 0.2 mm (when side trimming) -- Product length: 400–6000 mm Plus/minus 0.3 mm - 6-leveler (6-hi) leveler x 2units types -- Tension: 45 to 50 kg/mm2 -- Yield point: 28 kg/mm2 - Cutting method: Cut while running (flying), numerically controlled rocking type - flying shears -- (Cutting speed) 20–40/80 m/min -- Speed 2-speed change type --- 0.3 to 1.2 mm: 20 to 80 m/min --- 0.21–3 mm: 20–40 m/min -- Slow operation: 0.8 m/min -- Conveyor speed: 20~120m/min -- Cut count: up to 150 cuts/min -- (Product piling) --- Plate width: 500–1350 mm --- No1 piler: 400 to 3100 mm (also used as a reject filer) --- No2 piler: 400–6100 mm --- Load height: up to 600mm --- Load weight: up to 4 tons Line direction: From right to left on control panel Line: Approximately 13 m x 49.050 m (Major facilities) - Coil skid - Coil car - Pay off reel and a paper winder - Coil opener - Rough Leveler - Shear - No. 1 Looper Guide - Side guide and pinch roller - Side trimmer - Scrap winder x2 - No.1 Finisher Leveler (6-hi) - No2 Finisher Leveler (6-hi) - No 2 Looper Guide - Measuring roller, feed roller and paper-off reel - Shear - Conveyor - Cart - No1/No2 piler type - Hydraulic unit: Type - Valve stand type - (Coil skid) -- V-type fixed skid -- Coil maintenance: 1 coil -- Coil weight: up to 15 tonnes -- Coil diameter: 600 to 1800 mm -urethane rubber (Coil Car) Cradle roller type Hydraulic boost Electricity transfer driving type Two guide lots hydraulic cylinder elevating type (payoff reel and paper winder) Overhang, single-mant 4-segment type Paper reel motor: DC 5.5KW 400/1600 RPM, attached to brake Paper winder: cone type, (motor DC 1.5KW, 1750 RPM) (Coil Opener) Knife edge method (Rough Leveler) 2-stage (2hi) 5-body roller leveler Pinch rollers: 160 mm × 1450 mm 2 pieces, The upper part of the pinch roller is hydraulic cylinder press-down, and the lower roller is fixed 5 workload rollers 130mm x 1450mm The upper roller of the workload roller is electrically pressed, and the lower roller is fixed 0–40/80 m/min Two-stage change 0.3 to 1.6 mmt: 80 m/min 1.7 to 1.6 mmt: 40 m/min Motor: DC 18.5 KW, 1750 RPM, Brake Attachment Pressing motor: 2 1.5KW 100RPMs with brakes (Shear) Hydraulic up cut shear Knife size: 25 mm thickness × 150 mm width × 1450 mm length (No. 1 Looper Guide) Table lift Hydraulic cylinder operation method Loop: Light Volume Control Method Roller: 70 mm diameter × 1450 mm × 6 bonds, rubber lining roller (Side guide and pinch roller) Vertical Free Roller Electrically switched type Side guide roller: 90 mm diameter × 150 mm length × 6 bones Pinch Roller: 2nd Stage (2hi) Roller: 160 mm diameter × 1450 mm length × 2 bones Upper roller: pneumatic cylinder pressure free roller Lower Roller: Fixed Drive Roller (Side trimmer) Overhang Drive Cut 0–40/80 m/min 2-stage change type 0.3 to 1.6 mmt: 80 m/min 1.7 to 1.6 mmt: 40 m/min Cutter diameter: 320 mm / 190 mm internal diameter × 20 mm thickness Roller: 320 mm external diameter × 19 mm internal diameter × 20 mm thickness Motor: DC 5.5KW 1750RPM (Scrap winder) Two machines Link Pin Gauge Type (Hydraulic Cylinder Opening and Closing Type) Motor: 2 DC 2.2KW 1450 RPM (No1 Finisher Leveler) 6-level (6-hi) 17 leveler Thickness: 1.21–3.0 mm Speed: 6 to 40/80 m/min Thickness 0.3–1.2 mm 6–80 m/min Thickness 1.21–3 mm 6–40 m/min Pinch roller: 180 mm × 1750 mm × 2 bones The upper roll is a pneumatic cylinder. The lower roll is fixed Rubber lining drive roller Work roll: 60mm x 1750mm x 17e 8 for the upper roll, 9 for the lower roll Plated abrasive roller Medium roller: 50 mm × 1750 mm × 19 pieces 9 for the upper roll, 10 for the bottom roll Backup Roller: 88 mm Diameter x 50 mm Length x 7 rows Pressing Method: Lower Roller Parallel Pressing Pressing speed: 0.25 mm/sec Pressurization: plus or minus 5 mm Motor: DC 55KW 1750 RPM Brake Attachment (No2 Finisher Leveler) 6-level (6-hi) 17 leveler Plate thickness: 0.3–1.2 mm Speed: 5 to 80 m/min Pinch roller: 180 mm × 1750 mm × 2 bones The upper roll is a pneumatic cylinder. The lower roll is fixed Rubber lining drive roller Work roll: 35mm x 1750mm x 17bon 8 for the upper roll, 9 for the lower roll Plated abrasive roller Medium Roller: 32 mm × 1750 mm × 19 pieces 9 for the upper roll, 10 for the bottom roll Backup Roller: 99 mm Diameter x 50 mm Length x 7 rows Roller bearing type Pressing Method: Lower Roller Parallel Pressing Pressing speed: 0.25 mm/sec Pressurization: plus or minus 5 mm Motor: DC 35KW 1750RPM Brake Attachment (No. 2 Looper Guide) Table lift Hydraulic cylinder operation method Loop: How to control the amount of light (amount of light) Roller: 70 mm diameter × 1450 mm × 6 bonds, rubber lining roller (Measuring roll/feed roller/paper vinyl payoff reel) Measuring roller: The upper roll is pneumatic pressing, the lower roll is fixed, the pressing amount is 30 mm Feed roller: Upper roll is pneumatic cylinder press, lower roll is fixed, press load is 40 mm Motor: DC 2.2KW 1750RPM (Shear) Fluctuating Flying shear 0.3~3mm Speed: 2 groups of 20–40/80 m/min Thickness 0.3–1.6 mm 80 m/min Tlate thickness 1.6–3 mm 40 m/min Cut count: up to 150 cuts/min Cutting length: 400–6000 mm Electric up CUT shear Cut up and down knife die via motor, reducer, pinion stand crankshaft Knife: 20 mmt × 80 mm × 1400 mm × 1 set The top knife is a straight knife, and the bottom is a V-lock knife Adjustment: Wedge Motor: DC 75KW 550RPM (Conveyor) Belt conveyor type Belt width: 1200 mm Conveyor length: 3800 mm Motor DC 5.5KW 1450RPM Brake Attachment (No. 1 No. 2 piler) No1 piler: Combined use of reject truck, air blower Combined use of side conveyor No2 piler: Combined suction conveyor and air blower Loading height: 600 mm Lift: Hydraulic lift volume 650 mm Motor: 4 1.5KW 150RPM units for side guide end stoppers 2.2 KW 1500RPM for lifters 1.5KW for cart 7.5KW for blower (Hydraulic device) 70 kg/cm2 × 100 L/min Pen pump Motor: DC 18.5 KW 1000 RPM (Supply power) AC400 V,50 Hertz 3 Phase / AC200 V,50 Hertz 3 Phase (Control power) AC 200V, 50 Hz Single Phase (Compressed air) Compressed air required: 5 kg/cm2
Datasheet
Request / Contact
- SCHMITT REINHOLD GMBH
- Obernahmerstr. 74
- 58119 Hagen-Hohenlimburg
- Deutschland
-
+49 (0)2334 4847
+49 (0)2334 4840 -
info@reinhold-schmitt.de
www.reinhold-schmitt.de
#2008-056410 · Cut-to-length-lines
WILHELMSBURGER - - - 1975 -
Technical details
length tolerance ± 0,5 mm width tolerance ± 0,5 mm diagonal tolerance ± 1,0 mm line consisting of: double side decoiler leveler no. of leveling rolls 21 leveling roll diameter 35 mm flying shear magnetic conveyor table - length 10 m 2 output tables electric pneumatic hydraulic
Datasheet
Request / Contact
- Jansen Machinehandel BV
- Bredaseweg 210
- 4873 LA Etten-leur
- Nederland
-
+31 (0) 76 5015750
-
info@jansenmachinehandel.nl
www.jansenmachinehandel.nl
#2049-M825 · Cut-to-length-lines
Hydro Meca - 90L4C108H - - -
Technical details
Pipe cutting machine
Hydr. pressbrake
- Hans Klein Werkzeugmaschinenhandel GmbH
- Im Mühlgut 2-4
- 77815 Bühl
- Deutschland
-
0049 (0) 7223 9617-0
0049 (0) 7223 58512 -
info@klein-werkzeugmaschinen.de
www.klein-werkzeugmaschinen.de
#1052-01055 · Hydr. pressbrake
JONESCHEIT - HAMBURGER HYPM 70-2600 - - unbekannt -
Technical details
Accessories: upper and lower die (each in segments) on 2500 mm length, 2 upper die segments each 835 mm long, back stop
Datasheet
Request / Contact
- Bästlein
- Augsburger Str. 56
- 89312 Günzburg
- Deutschland
-
+49 (0) 8221 93037-0
+49 (0) 8221 93037-29 -
info@baestlein.com
www.baestlein.com
#1123-4020902 · Hydr. pressbrake
LAG - GHT 185-3000 - - NEU - DELEM DA-66T
Technical details
- Bästlein
- Augsburger Str. 56
- 89312 Günzburg
- Deutschland
-
+49 (0) 8221 93037-0
+49 (0) 8221 93037-29 -
info@baestlein.com
www.baestlein.com
#1123-4021135 · Hydr. pressbrake
FARINA - BSA PLUS 30200 - - NEU -
Technical details
- Bästlein
- Augsburger Str. 56
- 89312 Günzburg
- Deutschland
-
+49 (0) 8221 93037-0
+49 (0) 8221 93037-29 -
info@baestlein.com
www.baestlein.com
#1123-4021102 · Hydr. pressbrake
FARINA - PFO 130/30 - - NEU - CYBELEC VisiTouch
Technical details
Domestic equipments: - DELEM DA66T - 2D CNC control with LCD color display for control of 7 axes: Y1 = 1 ° cylinder Y2 = 2 ° cylinder X1 = horizontal movement of the backgauge X3 = horizontal movement of the stop finger / inclination R = vertical movement of the backgauge Z1-Z2 = lateral movement of the stop fingers - Top Dead Center - Speed ??changeover point - bending end - Deactivation point of the safety light barrier - Retreat stop - CNC controlled proportional pressure control - conical bending - USB port - DFC stator suspension compensation - Motorized back gauge model "AS" with 5 controlled axes - X-axis: 1000 mm stroke, X3-axis: 200 mm stroke - R-axis: 250 mm stroke - Hydraulic upper tool clamping make Wila, type: "Premium" NSCL-II-HC - Manual Unterwerkzeugklemmung, make Wila - Incl. Tools: sectioned, hardened and ground: Upper tool: Type: Wila BIU-021 Lower tool: Type: 4-V - Hydraulic compensation - "Platinum Package" consisting of: Active dynamic crowning Compensation of the stator suspension Sheet thickness measuring system diagnostic module - Active dynamic crowning device: Constant angle over the entire length Complete management of the crowning fully automatic Constant angle on the sides and in the middle No speed reduction The system works automatically and is almost invisible, no additional equipment required - Compensation of the stator suspension Bending sheet metal plates of different lengths without that The program parameters need to be changed. Bending of notched or perforated sheets without The program parameters need to be changed. Possibility of parts to work with reduced dimensions then test the workpiece with the actual dimensions without having to change the program parameters. No speed reduction during processing. The system works automatically and is almost invisible, no accessories required. - Sheet thickness measuring system Increased accuracy Fully automatic system Less waste Control of the material No speed reduction The system works automatically and is almost invisible, no accessories required - Soft start system "Start / Stop" to save energy - Control cabinet cooling - Hydraulic parts from Hoerbiger and Denison - Electrical parts from Rockwell Automation, Allen Bradley, Schneider, Siemens, Delem - Cabinet lighting through a LED strip - Machine lighting behind the machine with 2 LED strips - Footswitch - Laser safety system "DSP AP MSC" with height-adjustable Special arms. The system allows a speed change of only 2 mm from sheet metal and optimizes cycle times and maximum safety. - 2 front support arms (500mm): laterally movable and manually height adjustable by handwheel. - side and rear safety devices - Service key - Operating instructions and maintenance manual - Machine without oil - Machine according to standard 2006/42 / CE and CE certificate
- Bästlein
- Augsburger Str. 56
- 89312 Günzburg
- Deutschland
-
+49 (0) 8221 93037-0
+49 (0) 8221 93037-29 -
info@baestlein.com
www.baestlein.com
#1123-4021056 · Hydr. pressbrake
FARINA - PFO 130/30 - - NEU -
Technical details
Domestic equipments: - DELEM DA66T - 2D CNC control with LCD color display for control of 7 axes: Y1 = 1 ° cylinder Y2 = 2 ° cylinder X1 = horizontal movement of the backgauge X3 = horizontal movement of the stop finger / inclination R = vertical movement of the backgauge Z1-Z2 = lateral movement of the stop fingers - Top Dead Center - Speed ??changeover point - bending end - Deactivation point of the safety light barrier - Retreat stop - CNC controlled proportional pressure control - conical bending - USB port - DFC stator suspension compensation - Motorized back gauge model "AS" with 5 controlled axes - X-axis: 1000 mm stroke, X3-axis: 200 mm stroke - R-axis: 250 mm stroke - Hydraulic upper tool clamping make Wila, type: "Premium" NSCL-II-HC - Manual Unterwerkzeugklemmung, make Wila - Incl. Tools: sectioned, hardened and ground: Upper tool: Type: Wila BIU-021 Lower tool: Type: 4-V - Hydraulic compensation - "Platinum Package" consisting of: Active dynamic crowning Compensation of the stator suspension Sheet thickness measuring system diagnostic module - Active dynamic crowning device: Constant angle over the entire length Complete management of the crowning fully automatic Constant angle on the sides and in the middle No speed reduction The system works automatically and is almost invisible, no additional equipment required - Compensation of the stator suspension Bending sheet metal plates of different lengths without that The program parameters need to be changed. Bending of notched or perforated sheets without The program parameters need to be changed. Possibility of parts to work with reduced dimensions then test the workpiece with the actual dimensions without having to change the program parameters. No speed reduction during processing. The system works automatically and is almost invisible, no accessories required. - Sheet thickness measuring system Increased accuracy Fully automatic system Less waste Control of the material No speed reduction The system works automatically and is almost invisible, no accessories required - Soft start system "Start / Stop" to save energy - Control cabinet cooling - Hydraulic parts from Hoerbiger and Denison - Electrical parts from Rockwell Automation, Allen Bradley, Schneider, Siemens, Delem - Cabinet lighting through a LED strip - Machine lighting behind the machine with 2 LED strips - Footswitch - Laser safety system "DSP AP MSC" with height-adjustable Special arms. The system allows a speed change of only 2 mm from sheet metal and optimizes cycle times and maximum safety. - 2 front support arms (500mm): laterally movable and manually height adjustable by handwheel. - side and rear safety devices - Service key - Operating instructions and maintenance manual - Machine without oil - Machine according to standard 2006/42 / CE and CE certificate
- Bästlein
- Augsburger Str. 56
- 89312 Günzburg
- Deutschland
-
+49 (0) 8221 93037-0
+49 (0) 8221 93037-29 -
info@baestlein.com
www.baestlein.com
#1123-4021049 · Hydr. pressbrake
BAYKAL - APHS 31160 - - NEU - CYBELEC VisiTouch 19-2D
Technical details
- Bästlein
- Augsburger Str. 56
- 89312 Günzburg
- Deutschland
-
+49 (0) 8221 93037-0
+49 (0) 8221 93037-29 -
info@baestlein.com
www.baestlein.com
#1123-4020952 · Hydr. pressbrake
FARINA - GBP PLUS 30220 - - Neu - CYBELEC VisiTouch 19 2D
Technical details
- Bästlein
- Augsburger Str. 56
- 89312 Günzburg
- Deutschland
-
+49 (0) 8221 93037-0
+49 (0) 8221 93037-29 -
info@baestlein.com
www.baestlein.com
#1123-4021137 · Hydr. pressbrake
FARINA - BSA PLUS 40320 - - NEU -
Technical details
- Heinz Sanders GmbH
- Fresenburger Weg 4
- 49779 Niederlangen
- Deutschland
-
+49 (0) 5939 9406 40
+49 (0) 5939 9406 50 -
maschinen@heinz-sanders.de
www.heinz-sanders.de
#1125-2300004 · Hydr. pressbrake
PLACKE - EQPB-2 BabyPress 6,2t x 285 mm - - NEU - DELEM DA 41T
Technical details
• Basic version as a C-frame • Compact table model • Ideal for prototypes and small series • Very short setup time • Functionally simple • Wide range of applications • Low noise level • Low energy consumption • Easy handling including special equipment: - CNC control DELEM DA 41T
- Heinz Sanders GmbH
- Fresenburger Weg 4
- 49779 Niederlangen
- Deutschland
-
+49 (0) 5939 9406 40
+49 (0) 5939 9406 50 -
maschinen@heinz-sanders.de
www.heinz-sanders.de
#1125-2300003 · Hydr. pressbrake
ERMAK - POWER BEND FALCON 1270x60S - - NEU - DELEM DA 58 T
Technical details
-------------------------------------------------- --------- CNC press brake with special equipment * Version "ERGO" - knee room for the operator * flexible articulated arm mount for the controller * increased installation height * increased cylinder stroke * as well as increased bending beam speeds -------------------------------------------------- --------- Furnishing: - DELEM CNC control model DA-58T graphic/touch screen * 2D graphical programming * 15" TFT color screen with high resolution * Bending sequence calculation * Product programming and real size display * USB interface - Motorized backgauge with R-axis, on ball screws - X = 800 mm R = 250 mm with 2 stop fingers - controlled axes : Y1 - Y2 - X - R - Deer foot upper tool with PS 135.85-R08, system "A" with quick-change clamp - additional crowning device in the tool holder of the upper tool - 4V universal die block M 460 R with die shoe 60 mm mount - BOSCH/HOERBIGER hydr. components - SIEMENS electrical system - LEUZE light barrier behind the machine - FIESSLER AKAS laser with FPSC protection device v.d. machine - Swiveling control panel, mounted on the left - Front, foldable sheet metal support - Double foot control - CE mark / declaration of conformity - Operating manual: Machine and control in German - Safety manual : press brakes
- Heinz Sanders GmbH
- Fresenburger Weg 4
- 49779 Niederlangen
- Deutschland
-
+49 (0) 5939 9406 40
+49 (0) 5939 9406 50 -
maschinen@heinz-sanders.de
www.heinz-sanders.de
#1125-2300001 · Hydr. pressbrake
ERMAK - POWER BEND FALCON 3.135 - - NEU - DELEM DA 58 T
Technical details
-------------------------------------------------- --------- Press brake with special equipment * increased installation height * increased cylinder stroke * as well as increased bending beam speeds -------------------------------------------------- --------- Furnishing: - DELEM CNC control model DA-66T graphic/touch screen * 2D graphical programming * 17" TFT color screen with high resolution * Bending sequence calculation * Product programming and real size display * USB interface * intuitive, graphical entry of profiles * Automatic calculation of features: tool safety zones, Press force, bending tolerance, crown setting, stretched Length, embossing force, flattening, automatic rounding calculation * Radius programming * Graphic tool and product library * Collision monitoring * 3D visualization * 1GB memory - Motorized backgauge with R-axis, on ball screws - X = 800 mm R = 250 mm with 2 stop fingers - controlled axes Y1 - Y2 - X - R - C (crowning) - electr. Crowning controlled by CNC - Deer foot upper tool with PS 135.85-R08, system "A" with quick-change clamp - additional crowning device in the tool holder of the upper tool - 4V universal die block M 460 R with die shoe 60 mm mount - BOSCH/HOERBIGER hydr. components - SIEMENS electrical system - LEUZE light barrier behind the machine - FIESSLER AKAS laser with FPSC protection device v.d. machine - Swiveling control panel, mounted on the left - 2x front support arms "Sliding-System", with T-slot and cam - 1x double foot control - CE mark / declaration of conformity - Operating manual: Machine and control in German - Safety manual : press brakes
- Heinz Sanders GmbH
- Fresenburger Weg 4
- 49779 Niederlangen
- Deutschland
-
+49 (0) 5939 9406 40
+49 (0) 5939 9406 50 -
maschinen@heinz-sanders.de
www.heinz-sanders.de
#1125-2300006 · Hydr. pressbrake
ERMAK - SPEED BEND PRO 4.220 - - NEU - DELEM DA 66T
Technical details
HIGH-SPEED hydraulic press brake with increased installation height increased cylinder stroke increased projection -------------------------------------------------- ------- Furnishing: - DELEM CNC control model DA 66T - swiveling touch screen control unit - 7 controlled axes : Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning - electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm - on ball screws - controlled electr. Stop fingers Z1 + Z2 - split deer foot upper tool Roleri 135.85.R08, "System A" - with additional crowning of the upper wedge - Universal die block - LEUZE light barrier behind d. machine - BOSCH/HOERBIGER hydr. components - SIEMENS - electrical system - FIESSLER AKAS laser protection device in front of the machine (incl. FPSC) - 2 front support arms with SLIDING system (slide bearing) - Double foot control - CE mark / declaration of conformity - Operating manual: Machine and control in German - Safety manual : press brakes Special equipment included: - electric central lubrication
- Bästlein
- Augsburger Str. 56
- 89312 Günzburg
- Deutschland
-
+49 (0) 8221 93037-0
+49 (0) 8221 93037-29 -
info@baestlein.com
www.baestlein.com
#1123-4021174 · Hydr. pressbrake
FARINA - BSA 30135 - - NEU -
Technical details
- Intermach BV
- lange voor 71
- 8316BC Marknesse
- Niederlande
-
+31 (0)653235637
-
info@intermach.nl
www.intermach.nl
#2050-2010012 · Hydr. pressbrake
COLLY - 3000/140 - - NB -
Technical details
Stocknumber 2010012 Type of machine Pressbrake Make COLLY Type 3000/140 Build in nb Chamfer lenght 3000 mm Pressure 140 ton Stroke 250 mm Throat 310 mm Daylight 520 mm Additional information incl. 1 set of tooling
- Volz Werkzeugmaschinen
- Friedrich-Ebert Straße 78-80
- 58454 Witten-Annen
- Deutschland
-
+49 (0) 23 02 / 98 72 – 0
+49 (0) 23 02 / 98 72 - 50 -
anfrage@volz-witten.de
www.volz-witten.de
#1134-090006 · Hydr. pressbrake
HACO - ATLANTIC ERM 30135 - - 2022 - EasyBend 2D Touch
Technical details
Datasheet
Request / Contact
- HESSE+CO Maschinenfabrik GesmbH
- Straße 4 Objekt 8
- 2351 Wiener Neudorf
- Österreich
-
+43/2236/638 70-0
+43/2236/636 62 -
office@hesse-maschinen.com
https://www.hesse-maschinen.com
#1069-1794 · Hydr. pressbrake
HESSE by DURMA - PBF 2560 - - 2022 -
Technical details
DEMO MACHINE 3 axes (Y1, Y2, and X axis) CNC control DT-10 - intuitive touch-screen control (simple drawing of the bending outline with your finger) - user friendly programming in dialogue form - automatic calculation of bending sequence - automatic calculation of the blank sheet size - graphic product and tool memory - correction possibility - USB interfaces for backup and programm transportation - PC software, generating programms on the PC and transfer to the machine by USB CNC controlled back gauge with linear guide and ball screw spindles CNC crowning table intermediate clamps for upper tool upper tool1010/A/75°/0,8, sectioned,bending radius hardened and ground die holder for 60 mm dies die type2009/85°(V 16, 22, 35, 50 mm)sectioned, geteilt, bending radiihardened and ground laser safety device Fiessler AKASmounted on the upper beam sheet support arms protection covers on the sides andback side according to CE rules oilfilling users manual in GERMAN orENGLISH (sample photo shows mod. PBF 30200) ADVANTGES OF PBF SERIES: - compact structure - low cost due to serial production of standardised models without restrictions in quality and accuracy WE HAVE MORE THAN 600 REFERENCES!
Datasheet
Request / Contact
- HESSE+CO Maschinenfabrik GesmbH
- Straße 4 Objekt 8
- 2351 Wiener Neudorf
- Österreich
-
+43/2236/638 70-0
+43/2236/636 62 -
office@hesse-maschinen.com
https://www.hesse-maschinen.com
#1069-158 · Hydr. pressbrake
HESSE by ISITAN - Edgebender 1230 - - 2022 -
Technical details
DEMO MACHINE, MINT CONDITION NC control for immersion depth (Y) and back gauge (X) synchronization control by means of a torsion shaft sheet support arms light barriers die seat and die die seat with 4 V openings split upper tool, slightly cranked, divided pedal user manual in GERMAN incl. laser protection device Fiessler (sample photo)
Datasheet
Request / Contact
- HESSE+CO Maschinenfabrik GesmbH
- Straße 4 Objekt 8
- 2351 Wiener Neudorf
- Österreich
-
+43/2236/638 70-0
+43/2236/636 62 -
office@hesse-maschinen.com
https://www.hesse-maschinen.com
#1069-43 · Hydr. pressbrake
HESSE by DURMA - AD-R 30175 - - 2022 -
Technical details
DEMO MACHINE - MINT CONDITION 3 axes (Y1, Y2, X) CNC control DT-15 - 2D grafic display 15" - intuitive touch-screen control (simple drawing of the bending outline with your finger) - user friendly programming in dialogue form - automatic calculation of the bending sequence - automatic calculation of the blank sheet size - graphic product and tool memory - correction possibility - USB interfaces for backup and programm transportation - PC software, generating programms on the PC and transfer to the machine by USB servo motorized back gauge on linear guides and ball screws back gauge finger blocks on double linear guides CNC crowning table intermediate clamps for upper tool upper tool1010/A/75°/0,8/105, sectioned,bending radius hardened and ground die holder for 60 mm dies die type2009/85°(V 16, 22, 35, 50 mm)sectioned, geteilt, bending radiihardened and ground laser safety device Fiessler AKASmounted on the upper beam linear guided sheet support arms protection covers on the sides andback side according to CE rules oilfilling users manual in English or German ADVANTAGES OF AD-R COMPAIRED TO PBF: - more stroke, daylight opening and gap in side frame - higher approach- and retraction speed of upper beam - higher back gauge speed - back gauge fingers on double instead of single linear guide - more available options as Z1/Z2 axes, tandem execution, other CNC controls ... (sample photo) WE HAVE MORE THAN 620 REFERENCES!
Datasheet
Request / Contact
- SKM Industriemaschinen
- Röntgenstr. 3
- 89264 Weißenhorn
- Deutschland
-
+49 (0) 7309 954 986 0
+49 (0) 7309 954 986 1 -
info@skm-maschinen.de
www.skm-maschinen.de
#2032-1747 · Hydr. pressbrake
TECMASCHIN - APH630 - - 2021 - E21
Technical details
including upper tool including die Bending capacity steel: 2.5 mm to 3,200 mm *Machine may not comply with current UVV guidelines* *We expressly point out that we assume no responsibility for this* *Machine is sold as is*
- Amann Werkzeugmaschinen GmbH
- Landshuter Straße 1
- 85716 Unterschleißheim
- Deutschland
-
(0049) 89 317754 0
(0049) 89 3174262 -
info@amann-wzm.de
www.amann-wzm.de
#1006-92108 · Hydr. pressbrake
DENER - DD-M 10030 - - 2019 - Delem DA 66T
Technical details
*** Demonstration machine *** Y1 / Y2 servo electronic Hydraulic stamp clamping (WILA Premium) Hydraulic die clamping (WILA Premium) including motorized crowning Back gauge system "DENER" X-; R-; Z1-; Z2- axis FIESSLER AKAS LC II M Typ 4 (manual adjustment)with box bending Rolleri quick-change tools segmented: Punch TPR200.28.R1, die TMR100.12.30 total 3.050 mm length
Datasheet
Request / Contact
TOP Manufacturer:
HYDRO MECA - WILHELMSBURGER - HITACHI - VIGANO/RIVA -