Injection-moulding machine (rubber)

clamping force 450 kN︱injection volume 99 cm³︱screw diameter 30 mm︱platen size 860 x 320 mm︱closing stroke 406 mm︱

---

Condition: used, Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083 Clamping unit: - Clamping force: 450 kN - Opening travel: 406 mm - Heating plate size: 860 x 320 mm - Mould height min.: 264 mm - Max. plate spacing: 464 mm - Ejector stroke: 20 mm - Ejector force: 20 kN Injection unit: - Screw diameter: 30 mm - Screw length L/D: 16 - Dosing stroke: 140 mm - Stroke volume max.: 99 cm³ - Max. spray weight: 114 g - Screw speed: 20 - 300 rpm - Injection flow: 106 cm³/s - Injection flow increased: 71 cm³/s - Special injection pressure: 1451 bar - Spec. injection pressure increased: 2205 bar - Nozzle path: 530 mm - Operating hours: 54716 h - Pump drive power: 11 kW - Weight without oil: 6,500 kg - Dimensions L/W/height: 2,500 x 1,900 x 3,680 mm

clamping force 450 kN︱injection volume 135 cm³︱screw diameter 35 mm︱platen size 600 x 400 mm︱

---

Condition: used, Specification: C-frame injection moulding machine for TPE - used, from testing department Including PIOVAN dosing unit clamping unit: - clamping force: 450 kN - heating platen size: 600 x 400 mm - Clear width: 585 mm - Tool installation height min.: 185 mm - Max. stroke: 400 mm - sliding table: yes - Clamping direction: from below - Ejector / lifter: Up + Lo - Number of core pulls: 4 - Ejector stroke: 200 mm Injection unit: - Injection volume max.: 135 cm³ - Screw diameter: 35 mm - Connected load: 3x 400 V, 50 Hz - Weight approx.: 5,500 kg

clamping force 250 kN︱injection volume 49 cm³︱screw diameter 25 mm︱platen size 300 x 300 mm︱

---

Condition: used, specification: C-frame injection moulding machine - used clamping unit: - clamping force: 250 kN - heating platen size: 300 x 300 mm - clamping/opening stroke: 330 mm - Closing direction: from below - Lateral ejector: yes - Ejector stroke/force: 115 mm / 12 kN Injection unit: - Injection volume max.: 49 cm³ - Screw diameter: 25 mm - Screw length: 16 - Screw speed max.: 250 rpm - Injection: from above - Voltage: 3x 400 V, 50 Hz, N, PE - Connected load: 55 kW/92 A - Weight approx.: 3,500 kg Various accessories are also available: - Injection unit (25 screw) - 2 heating plates - Funnel and various small parts

clamping force 450 kN︱injection volume 99 cm³︱screw diameter 30 mm︱platen size 860 x 320 mm︱closing stroke 406 mm︱

---

Condition: used, Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083 Clamping unit: - Clamping force: 450 kN - Opening travel: 406 mm - Heating plate size: 860 x 320 mm - Mould height min.: 264 mm - Max. plate spacing: 464 mm - Ejector stroke: 20 mm - Ejector force: 20 kN Injection unit: - Screw diameter: 30 mm - Screw length L/D: 17 - Dosing stroke: 140 mm - Stroke volume max.: 99 cm³ - Max. spray weight: 114 g - Screw speed: 20 - 300 rpm - Injection flow: 106 cm³/s - Injection flow increased: 71 cm³/s - Special injection pressure: 1450 bar - Spec. injection pressure increased: 2210 bar - Nozzle path: 200 mm - Operating hours: 54716 h - Pump drive power: 15 kW - Weight without oil: 5,500 kg - Dimensions L/W/height: 2,500 x 1,900 x 3,680 mm

clamping force 800 kN︱injection volume 78 cm³︱screw diameter 25 mm︱platen size 570 x 552 mm︱

---

Condition: used, Specification: injection moulding machine for LSR - used Nr. 13EN08 clamping unit: - clamping force: 800 kN - size of heating platen: 570 x 552 mm - Between tie bars horizontally: 405 mm - Between tie bars vertically: 345 mm - Opening stroke: 310 mm - Ejector force: 25.4 kN - Ejector stroke: 100 mm - Mould installation height max.: 530 mm - Mould installation height min.: 250 mm - Bar diameter: 60 mm - Control: CC 90-A0 Injection unit: - Injection volume max.: 78 cm³ - Injection weight max.: 90 g - Screw diameter: 25 mm - Metering stroke: 160 mm - Screw speed max.: 20 - 400 rpm - Injection flow: 87 g/sec - Injection flow (increased): 64 g/sec - Specific injection pressure: 2400 bar - Nozzle stroke: 250 mm - Nozzle contact pressure: 47 kN Drive: - Voltage: 3x 400 V, 50 Hz, N, PE - Pump drive power: 15 kW - Oil filling: 185 l - Weight approx.: 4.000 kg

clamping force 800 kN︱injection volume 154 cm³︱screw diameter 35 mm︱platen size 570 x 552 mm︱

---

Condition: used, Specification: injection moulding machine for LSR - used Nr. 13EN12 clamping unit: - clamping force: 800 kN - size of heating platen: 570 x 552 mm - Between tie bars horizontally: 405 mm - Between tie bars vertically: 345 mm - Opening stroke: 310 mm - Ejector force: 25.4 kN - Ejector stroke: 100 mm - Mould installation height max.: 530 mm - Mould installation height min.: 250 mm - Bar diameter: 60 mm Injection unit: - Injection volume max.: 154 cm³ - Injection weight max.: 156 g - Screw diameter: 35 mm - Metering stroke: 160 mm - Screw speed max.: 20 - 320 rpm - Delivery flow: 35 g/sec - Injection flow: 148 g/sec - Injection flow (increased): 107 g/sec - Specific injection pressure: 1600 bar - Specific injection pressure increased: 2200 bar - Nozzle stroke: 250 mm - Nozzle contact pressure: 47 kN - Control: CC 90-A02 Drive: - Voltage: 3x 400 V, 50 Hz, N, PE - Pump drive power: 15 kW - Oil filling: 155 l - Weight approx.: 3,100 kg