,
Rete europea di concessionari di macchine per stoccaggio

Bitte einen Suchbegriff eingeben - Inserisci un termine di ricerca
Categoria:
    Produttore:
      macchine:
        trader:

          Outside profiling machine

          Machinelist: Outside profiling machine


          Outside profiling machine

          used Window production: wood Outside profiling machine Okoma UF 2 EG mit Schleifeinheit


          • Engelfried Maschinentechnik GmbH
          • Elisabethenstr. 41
          • 73432 Aalen
          • Deutschland

          • (0049)07361-98660
            (0049)07361-986640
          • info@engelfried.com
            www.engelfried.com
          #1305-6828 · Outside profiling machine

          Okoma - UF 2 EG mit Schleifeinheit - - gebraucht -

          Technical details
          Number of spindles 3 St.︱Number of tools 2/3 St.︱Spindle diameter 40/50 mm︱
          1 OKOMA folding machine model UF 2 EG ------------------------------------- 1. Energy data: - Operating voltage: 3 phases, 380 V, 50 Hz. - Compressed air: Air requirement: 13 NL/min. Operating pressure: 8 bar up. Air: according to Pneurop 6611 2. Profile spindle 1: - Spindle arrangement: right - Power 11 kW - Speed ??7000 rpm - Direction of rotation: synchronous and counter rotation - Spindle diameter 40 mm - Usable length 252 mm - Tool diameter max. 230 mm - U-movement of the profile spindle - Positioning vertically Drive: pneumatic cylinder 120 mm cycle for 2 tool positions Position sensor: limit switch - Positioning horizontally Drive: Pneumatic cylinder forward-back Position sensor: limit switch - Automatic immersion: immersion speed can be regulated for tear-free Fold over - Protective and suction hood with connecting piece 140 mm diameter. 3. Profile spindle 2: - Spindle arrangement: right - Power 11 kW - Speed ??7000 rpm - Direction of rotation: counter rotation - Spindle diameter 50 mm - Usable length 272 mm - Tool diameter max. 230 mm - U-movement of the profile spindle - Positioning vertically Drive: pneumatic cylinder 90 mm cycle for 3 tool positions Position sensor: limit switch - Positioning horizontally Drive: Pneumatic cylinder forward-back Position sensor: limit switch - Protective and suction hood with connecting piece 140 mm diameter. 4. Fitting milling device EG: - Spindle arrangement on the right - Drive: three-phase motor 3 kW - Speed ??6000 rpm - Spindle diameter 30 mm - Usable length 47 mm - Vertical positioning: none - Positioning horizontally Drive: Pneumatic cylinder forward-back Position sensor: limit switch (rear only) - Protective and suction hood with connection piece 80mm diameter 5. Stop: - 1st stop: in front of spindle 1 manual chip removal Quick adjustment via. parallelogram - 2nd stop: between spindles 1 and 2 Chip removal: pneumatically adjustable - 3rd stop: after spindle 2 Fixed stop 6. Grinder with automatic immersion and immersion 7. Feed: - Roller distance from axle to axle 130 mm - Roll diameter 110 mm - Roll width 50 mm - Feed can be swiveled away - with pneumatic travel control 8. Support rail for milling: - Rail length: approx. 3000 mm - Adjustment range forward: approx. 100 - 600 mm 9. Electrical control: - Programmable logic controller: Siemens electronics PC control, 30 programs, 380 V., 50 Hz. - Power section: Siemens S 5 - Non-contact limit switches More pictures on request! --------------------------- (technical data according to manufacturer - no guarantee!)
            Number of spindles 3 St.
            Number of tools 2/3 St.
            Spindle diameter 40/50 mm
            Description :
            1 OKOMA folding machine model UF 2 EG
            -------------------------------------
            1. Energy data:

            - Operating voltage: 3 phases, 380 V, 50 Hz.
            - Compressed air: Air requirement: 13 NL/min.
            Operating pressure: 8 bar
            up. Air: according to Pneurop 6611

            2. Profile spindle 1:

            - Spindle arrangement: right
            - Power 11 kW
            - Speed ??7000 rpm
            - Direction of rotation: synchronous and counter rotation
            - Spindle diameter 40 mm
            - Usable length 252 mm
            - Tool diameter max. 230 mm
            - U-movement of the profile spindle
            - Positioning vertically
            Drive: pneumatic cylinder 120 mm cycle
            for 2 tool positions
            Position sensor: limit switch

            - Positioning horizontally
            Drive: Pneumatic cylinder forward-back
            Position sensor: limit switch

            - Automatic immersion: immersion speed can be regulated for tear-free
            Fold over

            - Protective and suction hood with connecting piece 140 mm diameter.

            3. Profile spindle 2:

            - Spindle arrangement: right
            - Power 11 kW
            - Speed ??7000 rpm
            - Direction of rotation: counter rotation
            - Spindle diameter 50 mm
            - Usable length 272 mm
            - Tool diameter max. 230 mm
            - U-movement of the profile spindle
            - Positioning vertically
            Drive: pneumatic cylinder 90 mm cycle
            for 3 tool positions
            Position sensor: limit switch

            - Positioning horizontally
            Drive: Pneumatic cylinder forward-back
            Position sensor: limit switch
            - Protective and suction hood with connecting piece 140 mm diameter.

            4. Fitting milling device EG:

            - Spindle arrangement on the right
            - Drive: three-phase motor 3 kW
            - Speed ??6000 rpm
            - Spindle diameter 30 mm
            - Usable length 47 mm

            - Vertical positioning: none
            - Positioning horizontally
            Drive: Pneumatic cylinder forward-back

            Position sensor: limit switch (rear only)

            - Protective and suction hood with connection piece
            80mm diameter

            5. Stop:

            - 1st stop: in front of spindle 1
            manual chip removal
            Quick adjustment via. parallelogram
            - 2nd stop: between spindles 1 and 2
            Chip removal: pneumatically adjustable
            - 3rd stop: after spindle 2
            Fixed stop

            6. Grinder with automatic immersion and immersion


            7. Feed:

            - Roller distance from axle to axle 130 mm
            - Roll diameter 110 mm
            - Roll width 50 mm
            - Feed can be swiveled away
            - with pneumatic travel control

            8. Support rail for milling:

            - Rail length: approx. 3000 mm
            - Adjustment range forward: approx. 100 - 600 mm

            9. Electrical control:

            - Programmable logic controller: Siemens electronics
            PC control, 30 programs, 380 V., 50 Hz.
            - Power section: Siemens S 5
            - Non-contact limit switches

            More pictures on request!
            ---------------------------
            (technical data according to manufacturer - no guarantee!)


        • Engelfried Maschinentechnik GmbH
        • Elisabethenstr. 41
        • 73432 Aalen
        • Deutschland

        • Datasheet
          Request / Contact
          used Window production: wood Outside profiling machine WEINIG Univar 6 P


          • Engelfried Maschinentechnik GmbH
          • Elisabethenstr. 41
          • 73432 Aalen
          • Deutschland

          • (0049)07361-98660
            (0049)07361-986640
          • info@engelfried.com
            www.engelfried.com
          #1305-6827 · Outside profiling machine

          WEINIG - Univar 6 P - - gebraucht -

          Technical details
          Number of boring spindles 3 St.︱Number of tools 1.3/4.1. St.︱Spindle diameter 50,40 mm︱Spindle length 120,320,125 mm︱weight 2500 kg︱loading dimensions L x W x H 3800x1400x2000 mm︱table length 3470 mm︱
          Weinig Univar 6 P In order to sell ---------------------- Operating voltage: 380 volts, 50 periods. For milling around windows, doors and similar with uneven edges Profiles. Arrangement of the aggregates: 1. Synchronous spindle on the right, pneumatically clocked. 2. Profiling spindle on the right 3. Fitting spindle Profiling spindle suitable for holding several tools one on top of the other. Spindle movement pneumatic. The 1 spindle works in synchronization for tear-free milling. Respectively This spindle plunges the last 100 mm of a frame end with the Insert the appropriate tool into the wood to prevent tearing at the frame corners avoid. Machine stands, tables, stops: Machine body made of heavy, torsion-free and vibration-damping elements. Stops on the right in the profiling area made of Pertinax. Before Profiling spindle a split stop with sliding bar for short parts. Additional opening rail for large format frames. Feed system: Continuous, chainless feed equipped with rubber rollers. Blow-off device for feed rollers and table. Spindles, hood: Spindles with high concentricity and dynamically balanced. Extraction hoods designed for the cheapest chip flow. Easiest tool change Quick-opening hood lid. Machine operation, setting aids: Operating the machine from the front. Setting the stops for Tool diameter using mechanical number display. Machine electrics, motors, controls: Electrical design according to DIN VDE 0113 - Electrical equipment from Industrial machines EN 60204 IEC 204-1. Further electrical regulations are not taken into account. Engines dynamically balanced. Control of tool positions via selector switch on the control panel. Tools: Machine equipped with operating tools, but without Editing tools. SPINDLE 1 Synchronous spindle Number of tools: 1 Spindle speed: 6000 rpm Spindle diameter: 50mm Tool clamping length: 120 mm Tool diameter max. (milling): 232 mm Tool zero flight circle: 112-140 mm Basic position under table: 10 mm Motor strength: 4 KW (5.5 KW) SPINDLE 2 Number of tools: 4 Spindle stroke vertical: 3 x 80 mm = 4 tools Can be switched to 2 x 95 mm = 3 tools Spindle speed: 6000 rpm Spindle diameter: 50mm Tool clamping length: 320 mm Feed profiling unit: 8 m/min Feed roller width: 50mm/35mm Feed roller diameter: 95 mm Stop height: 70 mm Working width: min. 30 mm; max. 220 mm Working height: min. 30 mm; max. 100mm Workpiece length without tenon: min. 245 mm Tool diameter max. For zero diameter 112 mm: 210 mm For zero diameter 140 mm: 232 mm Tool diameter max. (milling): 232 mm Tool zero flight circle: 112-140 mm Basic position under table: 10/5 mm Motor strength: Spindle: 11 KW Feed: 1.1 KW Feed profiling unit: continuously 6-12 m/min Feed roller width: 50 mm Feed roller diameter: 95 mm Stop height: 70 mm Working width: min. 30 mm; max. 220 mm Working height: min. 30 mm; max. 100mm Workpiece length without tenon: min. 245 mm Special equipment: 3 Mechanical spindle brake for synchronous spindle, profiling spindle and Additional aggregates SPINDLE 3 1 fitting milling unit, right: for milling the fitting groove in the Milling pass or for grooving in the longitudinal profile. Pneumatic horizontal movement with selector switch in the control panel. Motor power: 2.2 KW Speed: 6000 rpm Spindle diameter: 40mm Clamping height: 125 mm Tool flight circle: min. 140 mm; max. 180 mm Basic position below table level: 10 mm Motor reinforcement for synchronous spindle from 4 KW to 7.5 KW Motor reinforcement for profiling spindle from 5.5 KW to 11 KW Screen controls for 99 window types. 1 type can hold up to 8 different parts contain. Manufacturing options: individual parts, milling. Data entry via Keyboard with integrated operator guidance and error diagnosis. Free-standing control cabinet --------------------------------- (technical data according to manufacturer - no guarantee!)
            Number of boring spindles 3 St.
            Number of tools 1.3/4.1. St.
            Spindle diameter 50,40 mm
            Spindle length 120,320,125 mm
            weight 2500 kg
            loading dimensions L x W x H 3800x1400x2000 mm
            table length 3470 mm
            Description :
            Weinig Univar 6 P
            In order to sell
            ----------------------
            Operating voltage: 380 volts, 50 periods.

            For milling around windows, doors and similar with uneven edges
            Profiles.

            Arrangement of the aggregates:
            1. Synchronous spindle on the right, pneumatically clocked.
            2. Profiling spindle on the right
            3. Fitting spindle

            Profiling spindle suitable for holding several tools one on top of the other.
            Spindle movement pneumatic.

            The 1 spindle works in synchronization for tear-free milling. Respectively
            This spindle plunges the last 100 mm of a frame end with the
            Insert the appropriate tool into the wood to prevent tearing at the frame
            corners
            avoid.

            Machine stands, tables, stops:
            Machine body made of heavy, torsion-free and vibration-damping
            elements. Stops on the right in the profiling area made of Pertinax. Before
            Profiling spindle a split stop with sliding bar for short parts.
            Additional opening rail for large format frames.

            Feed system:
            Continuous, chainless feed equipped with rubber rollers. Blow-off device
            for feed rollers and table.

            Spindles, hood:
            Spindles with high concentricity and dynamically balanced. Extraction hoods
            designed for the cheapest chip flow. Easiest tool change
            Quick-opening hood lid.

            Machine operation, setting aids:
            Operating the machine from the front. Setting the stops for
            Tool diameter using mechanical number display.

            Machine electrics, motors, controls:
            Electrical design according to DIN VDE 0113 - Electrical equipment from
            Industrial machines EN 60204 IEC 204-1.
            Further electrical regulations are not taken into account.

            Engines dynamically balanced.

            Control of tool positions via selector switch on the control panel.

            Tools:
            Machine equipped with operating tools, but without
            Editing tools.

            SPINDLE 1

            Synchronous spindle
            Number of tools: 1
            Spindle speed: 6000 rpm
            Spindle diameter: 50mm
            Tool clamping length: 120 mm
            Tool diameter max. (milling): 232 mm
            Tool zero flight circle: 112-140 mm
            Basic position under table: 10 mm
            Motor strength: 4 KW (5.5 KW)

            SPINDLE 2

            Number of tools: 4
            Spindle stroke vertical: 3 x 80 mm = 4 tools
            Can be switched to 2 x 95 mm = 3 tools
            Spindle speed: 6000 rpm
            Spindle diameter: 50mm
            Tool clamping length: 320 mm

            Feed profiling unit: 8 m/min
            Feed roller width: 50mm/35mm
            Feed roller diameter: 95 mm
            Stop height: 70 mm
            Working width: min. 30 mm; max. 220 mm
            Working height: min. 30 mm; max. 100mm
            Workpiece length without tenon: min. 245 mm


            Tool diameter max.
            For zero diameter 112 mm: 210 mm
            For zero diameter 140 mm: 232 mm

            Tool diameter max. (milling): 232 mm
            Tool zero flight circle: 112-140 mm
            Basic position under table: 10/5 mm
            Motor strength: Spindle: 11 KW Feed: 1.1 KW
            Feed profiling unit: continuously 6-12 m/min
            Feed roller width: 50 mm
            Feed roller diameter: 95 mm
            Stop height: 70 mm
            Working width: min. 30 mm; max. 220 mm
            Working height: min. 30 mm; max. 100mm
            Workpiece length without tenon: min. 245 mm

            Special equipment:

            3 Mechanical spindle brake for synchronous spindle, profiling spindle and
            Additional aggregates

            SPINDLE 3

            1 fitting milling unit, right: for milling the fitting groove in the
            Milling pass or for grooving in the longitudinal profile.
            Pneumatic horizontal movement with selector switch in the control panel.
            Motor power: 2.2 KW
            Speed: 6000 rpm
            Spindle diameter: 40mm
            Clamping height: 125 mm
            Tool flight circle: min. 140 mm; max. 180 mm
            Basic position below table level: 10 mm

            Motor reinforcement for synchronous spindle from 4 KW to 7.5 KW

            Motor reinforcement for profiling spindle from 5.5 KW to 11 KW

            Screen controls for 99 window types. 1 type can hold up to 8 different parts
            contain. Manufacturing options: individual parts, milling. Data entry via
            Keyboard with integrated operator guidance and error diagnosis.
            Free-standing control cabinet
            ---------------------------------

            (technical data according to manufacturer - no guarantee!)


        • Engelfried Maschinentechnik GmbH
        • Elisabethenstr. 41
        • 73432 Aalen
        • Deutschland

        • Datasheet
          Request / Contact
          used Window production: wood Outside profiling machine WEINIG Univar 10/3


          • Engelfried Maschinentechnik GmbH
          • Elisabethenstr. 41
          • 73432 Aalen
          • Deutschland

          • (0049)07361-98660
            (0049)07361-986640
          • info@engelfried.com
            www.engelfried.com
          #1305-2706 · Outside profiling machine

          WEINIG - Univar 10/3 - - gebraucht -

          Technical details
          Number of spindles 4 St.︱Number of tools 11 St.︱Spindle diameter 50,40 mm︱Spindle length 285,125 mm︱length 4000 mm︱width 2000 mm︱height 2200 mm︱
          Weinig Univar 10/3 folding machine --------------------------------- Machine will be cleaned and chcked before delivery For milling around windows, doors and the like with uneven circumferential profiles. Machine suitable for wood thickness 68 to 92 mm Time required per frame milling, medium size 1.20 x 1.20 m - approx. 2 minutes. The available tool positions are selected using a selector switch on the control panel retrieved. Machine with 3 hydraulically controlled right precision Lifting spindles for holding 3 tool sets, 2 x 95 mm spindle stroke per spindle The spindle stroke takes place in a U-movement, so that the opening is possible for short parts The milling stop remains as small as possible. Spindle stroke horizontally fine Adjustable for both tool positions from the operator side. Central lubrication for the spindle units. The 1. Spindle can be selected in right-left rotation. This spindle dips the last 100 mm of each frame end appropriate synchronization tool into the passing wood. Through this This prevents the tool of the subsequent milling spindle from running in the opposite direction working, causing tearouts. Excavation of the first 7 transport rollers using Footswitch. This shortens the lead time. An additional The support rail also allows large-format frames to be milled around. Continuous, chainless rubber roller feed with extreme short roller spacing. Height adjustment of the feed bar electrically readable. Electrical version according to VDE. Machine including operating tools, but without processing tools tools. Technical data: Working width min. 40 mm Working height min. 30 mm, max. 100 mm 1. Profiling spindle (synchronous and counter-rotation) -------------------------------------------------- -- Motor strength lifting spindle 11.0 kW Spindle speed 6000 rpm Spindle diameter 50 mm Clamping length 285 mm Tool zero flight circle 112 - 140 mm Max. tool - D : 232 mm Spindle stroke vertical 2 x 95 mm for 3 tools Basic position under table 10 mm (adjustable up to 20 mm) Spindle stroke horizontal 80 mm with synchronous automatic immersion 2. Profiling spindle ---------------------- Motor strength lifting spindle 11.0 kW Spindle speed 6000 rpm Spindle diameter 50 mm Clamping length 285 mm Tool zero flight circle 112 - 140 mm Max. tool - D : 232 mm Spindle stroke vertical 2 x 95 mm for 3 tools Basic position under table 10 mm (adjustable up to 20 mm) Spindle stroke horizontal 80 mm 3. Profiling spindle ---------------------- Motor strength lifting spindle 11.0 kW Spindle speed 6000 rpm Spindle diameter 50 mm Clamping length 285 mm Tool zero flight circle 112 - 140 mm Max. tool - D : 232 mm Spindle stroke vertical 2 x 95 mm for 3 tools Basic position under table 10 mm (adjustable up to 20 mm) Spindle stroke horizontal 80 mm 4. Profile spindle - fitting unit on the right ------------------------------------------------- For milling the fitting groove in the milling cycle or for grooving in the longitudinal profile. Pneumatic horizontal movement with Selector switch in the control panel. Motor 2.2 KW Speed 6,000 rpm Spindle diameter 40 mm Clamping height 125 mm, 2 tools Tool flight circle min. 140 mm, max. 180 mm Motor power feed 1.1 kW Feed speed 6 - 12 m/min. Feed rollers - D : 95 mm Feed roller width 50/30 mm Feed roller spacing 100/120 mm -------------------------------- Screen control with 150 programs. 1 program is each 1 individual part and includes 2 end profiles and 1 longitudinal profile. Pro programs are for end processing 20 different profiles can be selected for Longitudinal machining of 40 different profiles 1 can be selected (in turning mode 2). When manufacturing, e.g. a frame, up to 8 different programs (parts) can be saved. The program memory can be organized so that up to 18 frames or sashes with a maximum of 8 parts each can be stored. Manufacturing options: - Individual parts - Double parts - frame by frame - in series - Milling Data entry via keyboard with integrated Operator guidance and error diagnosis. ---------------------------------- Length: 4000mm (Length of frame milling ruler: 4500 mm) Width: 2000mm Height: 2200mm (Technical information according to the manufacturer, no guarantee!)
            Number of spindles 4 St.
            Number of tools 11 St.
            Spindle diameter 50,40 mm
            Spindle length 285,125 mm
            length 4000 mm
            width 2000 mm
            height 2200 mm
            Description :
            Weinig Univar 10/3 folding machine
            ---------------------------------
            Machine will be cleaned and chcked before delivery

            For milling around windows, doors and the like with uneven
            circumferential profiles. Machine suitable for wood thickness 68 to 92 mm

            Time required per frame milling, medium size 1.20 x 1.20 m - approx. 2 minutes.

            The available tool positions are selected using a selector switch on the
            control panel
            retrieved.

            Machine with 3 hydraulically controlled right precision
            Lifting spindles for holding 3 tool sets, 2 x 95 mm spindle stroke per spindle
            The spindle stroke takes place in a U-movement, so that the opening is possible
            for short parts
            The milling stop remains as small as possible. Spindle stroke horizontally fine
            Adjustable for both tool positions from the operator side.
            Central lubrication for the spindle units.

            The 1.
            Spindle can be selected in right-left rotation.

            This spindle dips the last 100 mm of each frame end
            appropriate synchronization tool into the passing wood. Through this
            This prevents the tool of the subsequent milling spindle from running in the
            opposite direction
            working, causing tearouts. Excavation of the first 7 transport rollers using
            Footswitch. This shortens the lead time. An additional
            The support rail also allows large-format frames to be milled around.

            Continuous, chainless rubber roller feed with extreme
            short roller spacing. Height adjustment of the feed bar
            electrically readable.

            Electrical version according to VDE.

            Machine including operating tools, but without processing tools
            tools.

            Technical data:

            Working width min. 40 mm
            Working height min. 30 mm, max. 100 mm

            1. Profiling spindle (synchronous and counter-rotation)
            -------------------------------------------------- --
            Motor strength lifting spindle 11.0 kW
            Spindle speed 6000 rpm
            Spindle diameter 50 mm
            Clamping length 285 mm
            Tool zero flight circle 112 - 140 mm
            Max. tool - D : 232 mm
            Spindle stroke vertical 2 x 95 mm for 3 tools
            Basic position under table 10 mm (adjustable up to 20 mm)
            Spindle stroke horizontal 80 mm
            with synchronous automatic immersion

            2. Profiling spindle
            ----------------------
            Motor strength lifting spindle 11.0 kW
            Spindle speed 6000 rpm
            Spindle diameter 50 mm
            Clamping length 285 mm
            Tool zero flight circle 112 - 140 mm
            Max. tool - D : 232 mm
            Spindle stroke vertical 2 x 95 mm for 3 tools
            Basic position under table 10 mm (adjustable up to 20 mm)
            Spindle stroke horizontal 80 mm

            3. Profiling spindle
            ----------------------
            Motor strength lifting spindle 11.0 kW
            Spindle speed 6000 rpm
            Spindle diameter 50 mm
            Clamping length 285 mm
            Tool zero flight circle 112 - 140 mm
            Max. tool - D : 232 mm
            Spindle stroke vertical 2 x 95 mm for 3 tools
            Basic position under table 10 mm (adjustable up to 20 mm)
            Spindle stroke horizontal 80 mm

            4. Profile spindle - fitting unit on the right
            -------------------------------------------------
            For milling the fitting groove in the milling cycle
            or for grooving in the longitudinal profile.
            Pneumatic horizontal movement with
            Selector switch in the control panel.
            Motor 2.2 KW
            Speed 6,000 rpm
            Spindle diameter 40 mm
            Clamping height 125 mm, 2 tools
            Tool flight circle min. 140 mm, max. 180 mm

            Motor power feed 1.1 kW
            Feed speed 6 - 12 m/min.
            Feed rollers - D : 95 mm
            Feed roller width 50/30 mm
            Feed roller spacing 100/120 mm
            --------------------------------

            Screen control with 150 programs. 1 program
            is each 1 individual part and includes 2 end profiles
            and 1 longitudinal profile. Pro programs are for end processing
            20 different profiles can be selected for
            Longitudinal machining of 40 different profiles
            1 can be selected (in turning mode 2).

            When manufacturing, e.g. a frame, up to
            8 different programs (parts) can be saved.

            The program memory can be organized so that up to
            18 frames or sashes with a maximum of 8 parts each can be stored.

            Manufacturing options:
            - Individual parts
            - Double parts
            - frame by frame
            - in series
            - Milling

            Data entry via keyboard with integrated
            Operator guidance and error diagnosis.
            ----------------------------------
            Length: 4000mm
            (Length of frame milling ruler: 4500 mm)
            Width: 2000mm
            Height: 2200mm

            (Technical information according to the manufacturer, no guarantee!)


        • Engelfried Maschinentechnik GmbH
        • Elisabethenstr. 41
        • 73432 Aalen
        • Deutschland

        • Datasheet
          Request / Contact
          •   
          •   
          • 1  
          •   
          •   

          TOP Manufacturer:

          WEINIG - OKOMA -